Power Factor
0.99 typical.

Emissions
EN 55022/CISPR 22, Class B Conducted. EN 61000-3-2, Harmonics.

Immunity
EN 61000-4-2, Level 3 Electrostatic Discharge. EN 61000-4-4, Level 3 Electrical Fast Transients. EN 61000-4-5, Level 3 Surge.

Input Surge
230VAC - 50 amps max. 115VAC - 25 amps max.

Efficiency
Greater than 80%.

Holdup Time
20 milliseconds from loss of AC power.

Outputs
See model selection table. Outputs are trim adjustable ±5%.

Output Polarity
Output is floating from chassis and can be referenced to ground as required.

Line Regulation
Less than 0.2% for full line change.

Load Regulation
Less than 1% for full load change.

Minimum Load
None required.

Ripple & Noise
1%, pk.-pk, 20 MHz bandwidth.

Operating temperature
0-70°C. Derate 2.5%/°C above 50°C.

Cooling
A minimum of 5 Linear feet per second is required, directed through the unit for full rating. See optional fan cover.

Temperature Coefficient
±0.02%/°C typical.

Dynamic Response
Peak transient less than ±2% for a step load change from 75% to 50% or 100% max. Output recovers within 300 microseconds.

Safety
Certified to UL 60950-1, CSA 22.2 No. 60950-1-03, EN 60950-1:2001.

Isolation
Conforms to safety agency standards.

Input Undervoltage
Protects against damage from undervoltage operation.

Soft Start
Units have soft start feature to protect critical components.

Overvoltage Protection
Standard on all models. Latching action. Recycle input to restart.

Reverse Voltage Protection
Output is protected up to 100% load ratings.

Overload and Short Circuit
Output is current limited with automatic recovery when overload is removed .

Current Share
Single wire current share.

Thermal Shutdown
Circuit cuts off supply in case of local over temperature. Units reset automatically when temperature returns to normal.

Enable
Enable pin must be shorted to Common for proper operation.

Remote Sensing
Standard on output.

Shock & Vibration
Shock per MIL-STD 810-E Method 516.4, Procedure I. Vibration per MIL-STD 810-E Method 514.4, Category 1, Procedure I.

Mechanical
Chassis dimensions are 1.58" H x 3.35" W x 11.15" L. Length includes end fan cover.

Connections
Connections via Positronic connector.

Warranty
Deltron's 2 year Standard Warranty applies.

OPTIONS

Redundancy (Code 01)
Redundant operation with Or-ing diode coupled with standard single wire current sharing for use as a hot pluggable N+1 redundant system.

Nylon Slides (Code 02)
Power supply chassis mounted slides provide ease of pluggability for use with Deltron model RA60A or equivalent racking system.

Fan Fail (Code 04)
TTL compatible logic signal provides warning when fan speed is inadequate to cool unit.

Field Terminations (Code 08)
Provides an alternative to Positronic hot-pluggable interface enabling customer to connect to power supply via field connections. Output terminals are 10-32 screws. Input terminals are via Euro block. A 14-pin header handles signals and function. Includes LEDs for AC Good, DC Good and Hi-Temp. Mating ribbon cable connector provided.

End Fan Cover (Code 32)
Optional cover with two brushless DC ball bearing end fans provides the required airflow for full rating. The end fan cover fits in 1.75" 1U rack height. It increases unit length by 1.30".

I²C Serial Interface
Consult Factory for specifications.

Racking System
The RA60A 1U high, 19" wide racking system is available for paralleling or N+1 redundant systems. The 1.75" H x 12.0" D rack accommodates up to four LA Series power supplies providing up to 2800 watts. .

LAC-1
Mating connector kit consisting of Positronic
PCIM right angle board-mount connector.